Products · Boilers & Heat Recovery

Steam Drums

To establish the project design basis for “Steam Drums”, confirm “Steam duty, circulation and droplet separation” and its inputs: Set steam load, feedwater quality, pressure/temperature, circulation philosophy, carryover limits and level/control needs from the boiler basis. Final values, supply limits and acceptance criteria are recorded in approved engineering documents; no generic capacity or catalogue guarantee is assumed.

AI-generated conceptual illustration of a horizontal steam drum; not a photograph of a Delham project

From project definition to delivery

Engineering intent and design approach

Engineering of Steam Drums concentrates on steam pressure and temperature, circulation, furnace or process-gas duty, feed-water quality, blowdown, pressure-part design, emissions, control range and operating flexibility. The selected configuration is verified against normal, minimum, start-up, shutdown and credible upset cases, then checked for operability, maintainability, energy use, process safety and site interfaces before the design is frozen.

The design basis for Steam Drums is defined from service data, design conditions, and battery limits. For this equipment, Steam duty, circulation and droplet separation and Fluid and design cases must be completed in the datasheet and design documents; performance values and guarantees are set only after the project basis is approved.

Mechanical design and materials

Materials, corrosion allowance, sour-service requirements, piping classes, nozzle design, insulation, coating, supports and maintenance access are coordinated with the actual process conditions and project code hierarchy.

Control, safeguarding and operation

Control philosophy, alarms and trips, cause-and-effect logic, interlocks, start-up and shutdown sequences, safe depressurization and operator access are developed consistently from the P&IDs through functional testing.

Layout, utilities and interfaces

Battery limits, tie-in points, structural loads, cabling, instrumentation, drains, vents, access routes, lifting envelopes and shipping constraints are controlled through coordinated models and interface drawings.

From project definition to delivery

Clear inputs and contract-ready outputs

Proposal quality depends on complete input data and an explicit acceptance basis. The following lists provide a practical starting point and are completed during technical clarification.

Recommended RFQ information

  • “Fluid and design cases”: Provide phase/properties, composition, pressure/temperature, corrosion/fouling, flashing/foaming and design cycles.
  • “Geometry, nozzles and internals”: Specify horizontal/vertical orientation, internals, demister/baffles, nozzles, manway, vent/drain, supports and piping loads.
  • Site and ambient data, hazardous-area classification and HSE requirements
  • Available utilities with pressure, temperature and capacity
  • Applicable standards, materials, supply limits and owner document formats

Typical engineering and supply deliverables

  • Equipment datasheet and design basis for “Steam Drums”, with service-relevant calculations where included in the supply scope.
  • PFDs, P&IDs, equipment list and technical datasheets
  • Control philosophy, cause and effect, I/O definition and utility summary
  • Plot plan, 3D model, foundation loads and fabrication drawings
  • Inspection and test plans, FAT records, final data book and commissioning support

Technical Datasheet

Technical Datasheet — Steam Drums

The output and pressure below describe one published natural-circulation boiler family supplied with a steam drum and evaporator bundle. They are not standalone drum ratings or universal limits.

Published equipment-family or project data only; not a universal standard limit or Delham rating/guarantee.
ParameterPublished valueReference basisApplicability / limit
Associated boiler steam outputUp to 20 t/hPublished maximum steam output for a high-pressure boiler family whose pressure section includes a steam drum.Boiler-family rating, not drum throughput by itself. Confirm load cases, circulation, steam purity/carryover and drum internals.
Associated boiler design pressureUp to 150 bar(g)Published maximum pressure for the cited high-pressure boiler family with a steam drum.Not automatically applicable to every drum or jurisdiction. Confirm code class, design temperature, water chemistry, corrosion allowance, materials and inspection.
Published circulation arrangementNatural circulation; drum above vertical evaporator bundleLayout stated for the cited boiler family.Drum volume, diameter, level span and separation efficiency still require thermal-hydraulic and mechanical design.

Published technical source

Delham Engineering

Define the scope around real project data

Send the available process data, battery limits and expected document list for a technical proposal. The engineering team will identify missing information through a structured clarification register.

Submit technical enquiry