Packages · Metering & Analyzer

Continuous Emission Monitoring Systems — CEMS

A continuous emission monitoring system (CEMS) measures the parameters defined for each emission source using an in-situ or extractive method. Measurement method and range, sample conditioning, quality checks and reporting are set from the applicable permit and project reference method; no general accuracy or regulatory compliance is assumed.

AI-generated conceptual illustration of a stack continuous emissions monitoring system; not a photograph of a Delham project

From project definition to delivery

Engineering intent and design approach

Engineering of Continuous Emission Monitoring Systems — CEMS concentrates on pollutant loading, concentration ranges and trends for monitored pollutants, representative sampling, analyzer response, calibration, data availability, reporting boundaries and environmental compliance. The selected configuration is verified against normal, minimum, start-up, shutdown and credible upset cases, then checked for operability, maintainability, energy use, process safety and site interfaces before the design is frozen.

Emission source, stack-gas flow/velocity, temperature, pressure and moisture, operating/load cases and target pollutant concentrations, start-up and shutdown cases, design life and acceptance criteria are agreed before equipment definition is frozen. The monitoring basis also fixes sample-point count/location, reference method, sample conditioning and transport, measurement span, response time, calibration/validation, data availability and shelter/hazardous-area requirements.

Mechanical design and materials

Materials, corrosion allowance, sour-service requirements, piping classes, nozzle design, insulation, coating, supports and maintenance access are coordinated with the actual process conditions and project code hierarchy.

Control, safeguarding and operation

Control philosophy, alarms and trips, cause-and-effect logic, interlocks, start-up and shutdown sequences, safe depressurization and operator access are developed consistently from the P&IDs through functional testing.

Layout, utilities and interfaces

Battery limits, tie-in points, structural loads, cabling, instrumentation, drains, vents, access routes, lifting envelopes and shipping constraints are controlled through coordinated models and interface drawings.

From project definition to delivery

Clear inputs and contract-ready outputs

Proposal quality depends on complete input data and an explicit acceptance basis. The following lists provide a practical starting point and are completed during technical clarification.

Recommended RFQ information

  • “Parameters and measurement ranges”: Define required parameters, concentration ranges, wet/dry basis and reference conditions only as required by the applicable method.
  • “Method and sample conditioning”: Specify in-situ or extractive measurement, probe location, filtration, heated transfer/conditioning and safe return or disposal.
  • Site and ambient data, hazardous-area classification and HSE requirements
  • Available utilities with pressure, temperature and capacity
  • Applicable standards, materials, supply limits and owner document formats

Typical engineering and supply deliverables

  • Equipment datasheet and design basis for “Continuous Emission Monitoring Systems — CEMS”, with service-relevant calculations where included in the supply scope.
  • PFDs, P&IDs, equipment list and technical datasheets
  • Calibration/validation philosophy, cause and effect, I/O list and data logging/reporting
  • Monitoring-point layout, sample-line routing, shelter/panels, cabling and connection details
  • Commissioning and FAT/SAT procedures, calibration/reference-gas records, data records, final data book and operator training

Technical Datasheet

Technical Datasheet — Continuous Emission Monitoring Systems — CEMS

These published values describe one modular system configuration, not emission limits, a universal CEMS range, Delham certification, or a project guarantee.

Published equipment-family or project data only; not a universal standard limit or Delham rating/guarantee.
ParameterPublished valueBasis / secondary dataApplication limit
Analyzer count in modular systemUp to 3Published modular CEMS configuration.Available analyzers and measured species depend on the selected module and monitoring plan.
Example system ambient range / enclosure5–40 °C; IP54Published environmental and ingress-protection data for one system configuration.Not a stack-gas measurement range or a universal enclosure requirement; site classification and local rules govern.

Published technical source

Delham Engineering

Define the scope around real project data

Send the available process data, battery limits and expected document list for a technical proposal. The engineering team will identify missing information through a structured clarification register.

Submit technical enquiry