Products · Fired Equipment & Process Heaters

Process Furnaces

To establish the project design basis for “Process Furnaces”, confirm “Process coil and thermal duty” and its inputs: Provide coil-fluid flow and properties, inlet/outlet conditions, thermal duty, pass arrangement and allowable pressure drop for operating cases. Final values, supply limits and acceptance criteria are recorded in approved engineering documents; no generic capacity or catalogue guarantee is assumed.

Process Furnaces

From project definition to delivery

Engineering intent and design approach

Engineering of Process Furnaces concentrates on absorbed duty, allowable tube heat flux, burner arrangement, draft, combustion control, tube metallurgy, refractory, emissions and safe light-off or shutdown logic. The selected configuration is verified against normal, minimum, start-up, shutdown and credible upset cases, then checked for operability, maintainability, energy use, process safety and site interfaces before the design is frozen.

The design basis for Process Furnaces is defined from service data, design conditions, and battery limits. For this equipment, Process coil and thermal duty and Fuel and process conditions must be completed in the datasheet and design documents; performance values and guarantees are set only after the project basis is approved.

Mechanical design and materials

Materials, corrosion allowance, sour-service requirements, piping classes, nozzle design, insulation, coating, supports and maintenance access are coordinated with the actual process conditions and project code hierarchy.

Control, safeguarding and operation

Control philosophy, alarms and trips, cause-and-effect logic, interlocks, start-up and shutdown sequences, safe depressurization and operator access are developed consistently from the P&IDs through functional testing.

Layout, utilities and interfaces

Battery limits, tie-in points, structural loads, cabling, instrumentation, drains, vents, access routes, lifting envelopes and shipping constraints are controlled through coordinated models and interface drawings.

From project definition to delivery

Clear inputs and contract-ready outputs

Proposal quality depends on complete input data and an explicit acceptance basis. The following lists provide a practical starting point and are completed during technical clarification.

Recommended RFQ information

  • “Fuel and process conditions”: Specify fuel composition/pressure/heating value, target temperature, pressure drop, site conditions and emission limits.
  • “Furnace, burner and heat-transfer surfaces”: Define radiant/convection arrangement, coils/tubes, burner, refractory, draft and cleaning strategy for the service.
  • Site and ambient data, hazardous-area classification and HSE requirements
  • Available utilities with pressure, temperature and capacity
  • Applicable standards, materials, supply limits and owner document formats

Typical engineering and supply deliverables

  • Equipment datasheet and design basis for “Process Furnaces”, with service-relevant calculations where included in the supply scope.
  • PFDs, P&IDs, equipment list and technical datasheets
  • Control philosophy, cause and effect, I/O definition and utility summary
  • Plot plan, 3D model, foundation loads and fabrication drawings
  • Inspection and test plans, FAT records, final data book and commissioning support

Technical Datasheet

Technical Datasheet — Process Furnaces

The duty below is the upper published value for one custom-designed refinery/petrochemical heater product family. It is a market benchmark, not a code-prescribed range or a Delham guarantee.

Published equipment-family or project data only; not a universal standard limit or Delham rating/guarantee.
ParameterPublished valueReference basisApplicability / limit
Published maximum absorbed-duty family ratingUp to 150 × 10⁶ kcal/h (≈174 MW) per unitPublished upper capacity for a single fired-heater unit in a refinery/petrochemical product portfolio.Single-family upper offer, not the capacity of every model or a universal minimum/maximum. Confirm absorbed duty, process cases, allowable tube flux, pressure drop and turndown.
Published configuration and fuel optionsVertical cylindrical / box / cabin; oil or natural gasConfigurations and fuel types listed for the same refinery-heater offering.Actual layout, burner count, fuel envelope, emissions and applicable API 530/API 560 requirements depend on the service and approved design basis.

Published technical source

Delham Engineering

Define the scope around real project data

Send the available process data, battery limits and expected document list for a technical proposal. The engineering team will identify missing information through a structured clarification register.

Submit technical enquiry